Book My Estimate

We have stumbled on this article relating to How to Install a Bathtub Yourself down the page on the net and thought it made sense to share it with you on this page.

Mounting a tub isn't exactly brain surgery, however it does need strong plumbing, carpentry, and often, tiling skills. Changing an old bathtub with a new one is also a moderately difficult task. If the old bathtub is readily available, the project can move quickly; if you need to open up a wall surface to eliminate the old bathtub as well as place the new bathtub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will certainly require an assistant to leave the old tub and set in the brand-new one. Make certain you have certified on your own for the task and also are comfortable attempting it. Instead of hiring a service provider to take control of a halfway-completed task, it is better to take into consideration utilizing one before you start. Opportunities are you might require a specialist plumber to make tube connections.
This short article will certainly help you install a new bathtub in your shower room if you have actually already bought a brand-new tub and also don't need to alter the arrangement of your previous water system pipes.
Your devices and also product checklist ought to comprise the following:

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Preparing for the Setup

To start with, the sustaining structure provided with the bathroom should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap includes a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps device to stop pressure on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its last placement.

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water system. After doing so, turn on the taps to drain any kind of water remaining in the system. The procedure of removing the existing taps can be fairly bothersome because of the limited gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly come from the pipelines. Once the supply pipes have been eliminated, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Prior to carrying on to fit the new faucets, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the new faucets to fit.

Installing the Tub

Using both wood boards under its feet, put the tub in the needed setting. The wooden boards are valuable in equally spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be attained by checking the spirit level and also changing the feet on the bath tub till the spirit level reads level.
To set up faucets, fit all-time low of the outermost adaptable faucet connector to the proper supply pipeline by making a compression join; then do the exact same for the other faucet.
Turn on the supply of water as well as inspect all joints and new pipework for leakages as well as tighten them if required. Fill the bathtub as well as also inspect the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling and also sealing around the bath tub must wait until the bath tub has actually been made use of at the very least once as this will certainly settle it into its last placement.

Fitting New Touches

If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the mounting hole in the bath/basin making certain that the washing machines are in area in between the tap as well as the sink. Safeguard the faucet in position with the producer given backnut. As soon as the tap is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap ports. The previous kind must be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

Tiling Around the Tub

In the location where the bathroom satisfies the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bath and the tiling, causing difficulties with wetness and also feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes and cartridges, and also can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before sealing, to allow for the motion experienced when the tub remains in usage. The sealer can split relatively very early if you do not think about this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the marketplace. It is a good idea to fit the ceramic tiles making use of waterproof or waterproof adhesive and cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I have been very inquisitive about How to Install a Bathtub Yourself and I really hope you enjoyed reading my blog entry. Sharing is good. You won't know, you will be helping someone out. I take joy in reading our article about How to Install a Bathtub.

Hot water issues? Connect now.